New NSE4_FGT-7.2 Exam Dumps: Latest Study Materials For Passing Fortinet NSE 4 - FortiOS 7.2 Exam

New NSE4_FGT-7.2 Exam Dumps: Latest Study Materials For Passing Fortinet NSE 4 – FortiOS 7.2 Exam

Eleanor2024-10-14T15:13:59+00:00

By Eleanor Fortinet, NSE 4 Network Security Professional

Are you looking to pass your NSE4_FGT-7.2 Fortinet NSE 4 – FortiOS 7.2 exam successfully? ITPrepare has the new Fortinet NSE4_FGT-7.2 exam dumps to help you pass the exam with ease. Our team of professionals has compiled the latest NSE4_FGT-7.2 exam questions with accurate answers to ensure your success. Get instant access to the latest NSE4_FGT-7.2 exam questions and answers by downloading the NSE4_FGT-7.2 pdf file and start preparing for the exam today. Boost your confidence and increase your chances of passing the NSE4_FGT-7.2 exam with ITPrepare’s latest study materials today.

Check Fortinet NSE4_FGT-7.2 Free Exam Demos Below

Page 1 of 6

1. Refer to exhibit.

An administrator configured the web filtering profile shown in the exhibit to block access to all social networking sites except Twitter. However, when users try to access twitter.com, they are redirected to a FortiGuard web filtering block page.

Based on the exhibit, which configuration change can the administrator make to allow Twitter while blocking all other social networking sites?

On the FortiGuard Category Based Filter configuration, set Action to Warning for Social Networking

On the Static URL Filter configuration, set Type to Simple

On the Static URL Filter configuration, set Action to Exempt.

On the Static URL Filter configuration, set Action to Monitor.

2. Which statement is correct regarding the use of application control for inspecting web applications?

Application control can identity child and parent applications, and perform different actions on them.

Application control signatures are organized in a nonhierarchical structure.

Application control does not require SSL inspection to identity web applications.

Application control does not display a replacement message for a blocked web application.

3. Which three options are the remote log storage options you can configure on FortiGate? (Choose three.)

FortiCache

FortiSIEM

FortiAnalyzer

FortiSandbox

FortiCloud

4. Which two protocol options are available on the CLI but not on the GUI when configuring an SD-WAN Performance SLA? (Choose two.)

DNS

ping

udp-echo

TWAMP

5. In which two ways can RPF checking be disabled? (Choose two )

Enable anti-replay in firewall policy.

Disable the RPF check at the FortiGate interface level for the source check

Enable asymmetric routing.

Disable strict-arc-check under system settings.

6. Refer to the exhibit.

The exhibit contains a network diagram, virtual IP, IP pool, and firewall policies configuration.

The WAN (port1) interface has the IP address 10.200. 1. 1/24.

The LAN (port3) interface has the IP address 10 .0.1.254. /24.

The first firewall policy has NAT enabled using IP Pool.

The second firewall policy is configured with a VIP as the destination address.

Which IP address will be used to source NAT the internet traffic coming from a workstation with the IP address 10.0.1.10?

10.200.1.1

10.200.3.1

10.200.1.100

10.200.1.10

7. Which feature in the Security Fabric takes one or more actions based on event triggers?

Fabric Connectors

Automation Stitches

Security Rating

Logical Topology

8. CORRECT TEXT

Which two policies must be configured to allow traffic on a policy-based next-generation firewall (NGFW) FortiGate? (Choose two.)

Security policy

SSL inspection and authentication policy

9. Refer to the exhibit.

An administrator has configured a performance SLA on FortiGate, which failed to generate any traffic.

Why is FortiGate not sending probes to 4.2.2.2 and 4.2.2.1 servers? (Choose two.)

The Detection Mode setting is not set to Passive.

Administrator didn't configure a gateway for the SD-WAN members, or configured gateway is not valid.

The configured participants are not SD-WAN members.

The Enable probe packets setting is not enabled.

10. Refer to the exhibit.

Review the Intrusion Prevention System (IPS) profile signature settings.

Which statement is correct in adding the FTP.Login.Failed signature to the IPS sensor profile?

The signature setting uses a custom rating threshold.

The signature setting includes a group of other signatures.

Traffic matching the signature will be allowed and logged.

Traffic matching the signature will be silently dropped and logged.

Page 2 of 6

11. Examine this PAC file configuration.

Which of the following statements are true? (Choose two.)

Browsers can be configured to retrieve this PAC file from the FortiGate.

Any web request to the 172.25. 120.0/24 subnet is allowed to bypass the proxy.

All requests not made to Fortinet.com or the 172.25. 120.0/24 subnet, have to go through altproxy.corp.com: 8060.

Any web request fortinet.com is allowed to bypass the proxy.

12. Refer to the exhibits.

The exhibits show the SSL and authentication policy (Exhibit A) and the security policy (Exhibit B) for Facebook.

Users are given access to the Facebook web application. They can play video content hosted on Facebook but they are unable to leave reactions on videos or other types of posts.

Which part of the policy configuration must you change to resolve the issue?

Make SSL inspection needs to be a deep content inspection.

Force access to Facebook using the HTTP service.

Get the additional application signatures are required to add to the security policy.

Add Facebook in the URL category in the security policy.

13. What two changes can the administrator make to resolve the issue without affecting any existing services running through FortiGate? (Choose two.)

Create a new firewall policy with the new HTTP service and place it above the existing HTTP policy.

Create a new service object for HTTP service and set the session TTL to never

Set the TTL value to never under config system-ttl

Set the session TTL on the HTTP policy to maximum

14. An administrator is running the following sniffer command:

Which three pieces of Information will be Included in me sniffer output? {Choose three.)

Interface name

Packet payload

Ethernet header

IP header

Application header

15. Refer to the exhibit.

Examine the intrusion prevention system (IPS) diagnostic command.

Which statement is correct If option 5 was used with the IPS diagnostic command and the outcome was a decrease in the CPU usage?

The IPS engine was inspecting high volume of traffic.

The IPS engine was unable to prevent an intrusion attack .

The IPS engine was blocking all traffic.

The IPS engine will continue to run in a normal state.

16. Which CLI command allows administrators to troubleshoot Layer 2 issues, such as an IP address conflict?

get system status

get system performance status

diagnose sys top

get system arp

17. Examine this FortiGate configuration:

How does the FortiGate handle web proxy traffic coming from the IP address 10.2.1.200 that requires authorization?

It always authorizes the traffic without requiring authentication.

It drops the traffic.

It authenticates the traffic using the authentication scheme SCHEME2.

It authenticates the traffic using the authentication scheme SCHEME1.

18. Examine the exhibit, which contains a virtual IP and firewall policy configuration.

The WAN (port1) interface has the IP address 10.200. 1. 1/24. The LAN (port2) interface has the IP address 10.0. 1.254/24.

The first firewall policy has NAT enabled on the outgoing interface address. The second firewall policy is configured with a VIP as the destination address.

Which IP address will be used to source NAT the Internet traffic coming from a workstation with the IP address 10.0.1.10/24?

10.200. 1. 10

Any available IP address in the WAN (port1) subnet 10.200. 1.0/24 66 of 108

10.200. 1. 1

10.0. 1.254

19. Refer to the exhibit.

Given the interfaces shown in the exhibit. which two statements are true? (Choose two.)

Traffic between port2 and port2-vlan1 is allowed by default.

port1-vlan10 and port2-vlan10 are part of the same broadcast domain.

port1 is a native VLA

port1-vlan and port2-vlan1 can be assigned in the same VDOM or to different VDOMs.

20. The HTTP inspection process in web filtering follows a specific order when multiple features are enabled in the web filter profile.

What order must FortiGate use when the web filter profile has features enabled, such as safe search?

DNS-based web filter and proxy-based web filter

Static URL filter, FortiGuard category filter, and advanced filters

Static domain filter, SSL inspection filter, and external connectors filters

FortiGuard category filter and rating filter

Page 3 of 6

21. Which two statements are correct regarding FortiGate FSSO agentless polling mode? (Choose two.)

FortiGate points the collector agent to use a remote LDAP server.

FortiGate uses the AD server as the collector agent.

FortiGate uses the SMB protocol to read the event viewer logs from the DCs.

FortiGate queries AD by using the LDAP to retrieve user group information.

22. Which two statements about FortiGate FSSO agentless polling mode are true? (Choose two.)

FortiGate uses the AD server as the collector agent.

FortiGate uses the SMB protocol to read the event viewer logs from the DCs.

FortiGate does not support workstation check .

FortiGate directs the collector agent to use a remote LDAP server.

23. Which of statement is true about SSL VPN web mode?

The tunnel is up while the client is connected.

It supports a limited number of protocols.

The external network application sends data through the VP

It assigns a virtual IP address to the client.

24. View the exhibit.

Which of the following statements are correct? (Choose two.)

This setup requires at least two firewall policies with the action set to IPsec.

Dead peer detection must be disabled to support this type of IPsec setup.

The TunnelB route is the primary route for reaching the remote site. The TunnelA route is used only if the TunnelB VPN is down.

This is a redundant IPsec setup.

25. Which CLI command will display sessions both from client to the proxy and from the proxy to the servers?

diagnose wad session list

diagnose wad session list | grep hook-pre&&hook-out

diagnose wad session list | grep hook=pre&&hook=out

diagnose wad session list | grep "hook=pre"&"hook=out"

26. Which two inspection modes can you use to configure a firewall policy on a profile-based next-generation firewall (NGFW)? (Choose two.)

Proxy-based inspection

Certificate inspection

Flow-based inspection

Full Content inspection

27. Refer to the exhibit.

The exhibit displays the output of the CLI command: diagnose sys ha dump-by vcluster.

Which two statements are true? (Choose two.)

FortiGate SN FGVM010000065036 HA uptime has been reset.

FortiGate devices are not in sync because one device is down.

FortiGate SN FGVM010000064692 is the primary because of higher HA uptime.

FortiGate SN FGVM010000064692 has the higher HA priority.

28. What is the effect of enabling auto-negotiate on the phase 2 configuration of an IPsec tunnel?

FortiGate automatically negotiates different local and remote addresses with the remote peer.

FortiGate automatically negotiates a new security association after the existing security association expires.

FortiGate automatically negotiates different encryption and authentication algorithms with the remote peer.

FortiGate automatically brings up the IPsec tunnel and keeps it up, regardless of activity on the IPsec tunnel.

29. A network administrator wants to set up redundant IPsec VPN tunnels on FortiGate by using two IPsec VPN tunnels and static routes.

* All traffic must be routed through the primary tunnel when both tunnels are up

* The secondary tunnel must be used only if the primary tunnel goes down

* In addition, FortiGate should be able to detect a dead tunnel to speed up tunnel failover

Which two key configuration changes are needed on FortiGate to meet the design requirements? (Choose two,)

Configure a high distance on the static route for the primary tunnel, and a lower distance on the static route for the secondary tunnel.

Enable Dead Peer Detection.

Configure a lower distance on the static route for the primary tunnel, and a higher distance on the static route for the secondary tunnel.

Enable Auto-negotiate and Autokey Keep Alive on the phase 2 configuration of both tunnels.

30. In an explicit proxy setup, where is the authentication method and database configured?

Proxy Policy

Authentication Rule

Firewall Policy

Authentication scheme

Page 4 of 6

31. A network administrator is configuring a new IPsec VPN tunnel on FortiGate. The remote peer IP address is dynamic. In addition, the remote peer does not support a dynamic DNS update service.

What type of remote gateway should the administrator configure on FortiGate for the new IPsec VPN tunnel to work?

Static IP Address

Dialup User

Dynamic DNS

Pre-shared Key

32. Refer to the exhibit.

An administrator is running a sniffer command as shown in the exhibit.

Which three pieces of information are included in the sniffer output? (Choose three.)

Interface name

Ethernet header

IP header

Application header

Packet payload

33. Which statements best describe auto discovery VPN (ADVPN). (Choose two.)

It requires the use of dynamic routing protocols so that spokes can learn the routes to other spokes.

ADVPN is only supported with IKEv2.

Tunnels are negotiated dynamically between spokes.

Every spoke requires a static tunnel to be configured to other spokes so that phase 1 and phase 2 proposals are defined in advance.

34. An administrator does not want to report the logon events of service accounts to FortiGate.

What setting on the collector agent is required to achieve this?

Add the support of NTLM authentication.

Add user accounts to Active Directory (AD).

Add user accounts to the FortiGate group fitter.

Add user accounts to the Ignore User List.

35. Which statement is correct regarding the inspection of some of the services available by web applications embedded in third-party websites?

The security actions applied on the web applications will also be explicitly applied on the third-party websites.

The application signature database inspects traffic only from the original web application server.

FortiGuard maintains only one signature of each web application that is unique.

FortiGate can inspect sub-application traffic regardless where it was originated.

36. Refer to the exhibit showing a debug flow output.

Which two statements about the debug flow output are correct? (Choose two.)

The debug flow is of ICMP traffic.

A firewall policy allowed the connection.

A new traffic session is created.

The default route is required to receive a reply.

37. Refer to the exhibit.

The exhibit shows a diagram of a FortiGate device connected to the network, the firewall policy and VIP configuration on the FortiGate device, and the routing table on the ISP router.

When the administrator tries to access the web server public address (203.0.113.2) from the internet, the connection times out. At the same time, the administrator runs a sniffer on FortiGate to capture incoming web traffic to the server and does not see any output.

Based on the information shown in the exhibit, what configuration change must the administrator make to fix the connectivity issue?

Configure a loopback interface with address 203.0.113.2/32.

In the VIP configuration, enable arp-reply.

Enable port forwarding on the server to map the external service port to the internal service port.

In the firewall policy configuration, enable match-vip.

38. Why does FortiGate keep TCP sessions in the session table for some seconds even after both sides (client and server) have terminated the session?

To remove the NAT operation.

To generate logs

To finish any inspection operations.

To allow for out-of-order packets that could arrive after the FIN/ACK packets.

39. An administrator must disable RPF check to investigate an issue.

Which method is best suited to disable RPF without affecting features like antivirus and intrusion prevention system?

Enable asymmetric routing, so the RPF check will be bypassed.

Disable the RPF check at the FortiGate interface level for the source check.

Disable the RPF check at the FortiGate interface level for the reply check .

Enable asymmetric routing at the interface level.

40. When configuring a firewall virtual wire pair policy, which following statement is true?

Any number of virtual wire pairs can be included, as long as the policy traffic direction is the same.

Only a single virtual wire pair can be included in each policy.

Any number of virtual wire pairs can be included in each policy, regardless of the policy traffic direction settings.

Exactly two virtual wire pairs need to be included in each policy.

Page 5 of 6

41. 1.Refer to the exhibit.

Based on the raw log, which two statements are correct? (Choose two.)

Traffic is blocked because Action is set to DENY in the firewall policy.

Traffic belongs to the root VDO

This is a security log.

Log severity is set to error on FortiGate.

42. Which statement about video filtering on FortiGate is true?

Full SSL Inspection is not required.

It is available only on a proxy-based firewall policy.

It inspects video files hosted on file sharing services.

Video filtering FortiGuard categories are based on web filter FortiGuard categories.

43. What is the limitation of using a URL list and application control on the same firewall policy, in NGFW policy-based mode?

It limits the scanning of application traffic to the DNS protocol only.

It limits the scanning of application traffic to use parent signatures only.

It limits the scanning of application traffic to the browser-based technology category only.

It limits the scanning of application traffic to the application category only.

44. Refer to the exhibit.

Which contains a session diagnostic output.

Which statement is true about the session diagnostic output?

The session is in SYN_SENT state.

The session is in FIN_ACK state.

The session is in FTN_WAIT state.

The session is in ESTABLISHED state.

45. Which of the following conditions must be met in order for a web browser to trust a web server certificate signed by a third-party CA?

The public key of the web server certificate must be installed on the browser.

The web-server certificate must be installed on the browser.

The CA certificate that signed the web-server certificate must be installed on the browser.

The private key of the CA certificate that signed the browser certificate must be installed on the browser.

46. A FortiGate is operating in NAT mode and configured with two virtual LAN (VLAN) sub interfaces added to the physical interface.

Which statements about the VLAN sub interfaces can have the same VLAN ID, only if they have IP addresses in different subnets.

The two VLAN sub interfaces can have the same VLAN ID, only if they have IP addresses in different subnets.

The two VLAN sub interfaces must have different VLAN IDs.

The two VLAN sub interfaces can have the same VLAN ID, only if they belong to different VDOMs.

The two VLAN sub interfaces can have the same VLAN ID, only if they have IP addresses in the same subnet.

47. Refer to the exhibits to view the firewall policy (Exhibit A) and the antivirus profile (Exhibit B).

Which statement is correct if a user is unable to receive a block replacement message when downloading an infected file for the first time?

The firewall policy performs the full content inspection on the file.

The flow-based inspection is used, which resets the last packet to the user.

The volume of traffic being inspected is too high for this model of FortiGate.

The intrusion prevention security profile needs to be enabled when using flow-based inspection mode.

48. Which three statements are true regarding session-based authentication? (Choose three.)

HTTP sessions are treated as a single user.

IP sessions from the same source IP address are treated as a single user.

It can differentiate among multiple clients behind the same source IP address.

It requires more resources.

It is not recommended if multiple users are behind the source NAT

49. Refer to the exhibits.

The exhibits show the firewall policies and the objects used in the firewall policies.

The administrator is using the Policy Lookup feature and has entered the search criteria shown in the exhibit.

Which policy will be highlighted, based on the input criteria?

Policy with ID 4.

Policy with ID 5.

Policies with ID 2 and 3.

Policy with ID 4.

50. Which two statements are true when FortiGate is in transparent mode? (Choose two.)

By default, all interfaces are part of the same broadcast domain.

The existing network IP schema must be changed when installing a transparent mode.

Static routes are required to allow traffic to the next hop.

FortiGate forwards frames without changing the MAC address.

Page 6 of 6

51. Which two attributes are required on a certificate so it can be used as a CA certificate on SSL Inspection? (Choose two.)

The keyUsage extension must be set to keyCertSign.

The common name on the subject field must use a wildcard name.

The issuer must be a public C

The CA extension must be set to TRU

52. What is the limitation of using a URL list and application control on the same firewall policy, in NGFW policy-based mode?

It limits the scope of application control to the browser-based technology category only.

It limits the scope of application control to scan application traffic based on application category only.

It limits the scope of application control to scan application traffic using parent signatures only

It limits the scope of application control to scan application traffic on DNS protocol only.

53. Which two settings can be separately configured per VDOM on a FortiGate device? (Choose two.)

System time

FortiGuaid update servers

Operating mode

NGFW mode

54. Which of the following statements is true regarding SSL VPN settings for an SSL VPN portal?

By default, FortiGate uses WINS servers to resolve names.

By default, the SSL VPN portal requires the installation of a client's certificate.

By default, split tunneling is enabled.

By default, the admin GUI and SSL VPN portal use the same HTTPS port.

55. A network administrator has enabled SSL certificate inspection and antivirus on FortiGate. When downloading an EICAR test file through HTTP, FortiGate detects the virus and blocks the file. When downloading the same file through HTTPS, FortiGate does not detect the virus and the file can be downloaded.

What is the reason for the failed virus detection by FortiGate?

The website is exempted from SSL inspection.

The EICAR test file exceeds the protocol options oversize limit.

The selected SSL inspection profile has certificate inspection enabled.

The browser does not trust the FortiGate self-signed CA certificate.

New NSE4_FGT-7.2 Exam Dumps: Latest Study Materials For Passing Fortinet NSE 4 – FortiOS 7.2 Exam

New NSE4_FGT-7.2 Exam Dumps: Latest Study Materials For Passing Fortinet NSE 4 – FortiOS 7.2 Exam

Check Fortinet NSE4_FGT-7.2 Free Exam Demos Below

Share this post

Author

Related Posts