NetApp Certified Storage Installation Engineer, ONTAP (NCSIE ONTAP) NS0-184 Exam Dumps Updated

Eleanor2024-10-14T15:30:10+00:00

By Eleanor NCSIE ONTAP, NetApp, Network Appliance

To help you prepare for the NS0-184 NetApp Certified Storage Installation Engineer, ONTAP exam well and achieve success easily, we today have updated the NS0-184 exam dumps.

Exam Code: NS0-184
Exam Name: NetApp Certified Storage Installation Engineer, ONTAP
Exam Version: V10.02
Exam Q&As: 371
Exam Format: PDF File (Download Online)
Up-to-Date: August 18, 2022

The top-related NS0-184 exam dumps questions cover each exam objective, candidates who choose the ITPrepare’s updated NS0-184 exam dumps can practice all those questions and answers well to make sure they can pass the NetApp Certified Storage Installation Engineer, ONTAP exam easily.

Here have NS0-184 free demo dumps online for checking the updated NS0-184 exam dumps:

Page 1 of 8

1. You have completed a base installation and system registration of an AFF A250 system, but you notice that you have one failed drive. Neither “un-failing” nor reseating the drive helped to repair it. You must ensure proper replacement of the failed drive.

In this scenario, which two actions should you take? (Choose two.)

Ask the customer to open a technical case with NetApp Support.

Ask the customer for a drive with the same capacity and replace it.

Run Active IQ Config Advisor to collect all the logs on the system.

Power off the system until the drive has been replaced.

2. You have a 4-node ONTAP 9.8 cluster with a FAS8700 HA pair that serves iSCSI LUNs. You are adding a new AFF A250 HA pair to the cluster with new iSCSI SAN LIFs. You need to allow non-optimized data paths from the AFF A250 nodes to the existing LUNs on the FAS8700 nodes.

In this scenario, which two ONTAP configuration settings must you verify? (Choose two.)

port sets

switch zoning

reporting nodes

failover groups

3. A new AFF8200 has a four-port UTA2 adapter installed in slot 2. Using the ucadmin command, you see that these ports are configured for FC.

Which port names are correct in this scenario?

e0a/0a, e0b/0b, e0c/0c, e0d/od

e2a/2a, e2b/2b, e2c/2c, e2d/2d

e2a, e2b, e2c, e2d

2a, 2b, 2c, 2d

4. Click the Exhibit button.

What are two functions of the four Ethernet switches in the supported configuration that is shown in the exhibit? (Choose two.)

to provide a direct connection for the SnapMirror Synchronous (SM-S)

to install cross-site cluster management switches

to provide connectivity for NVRAM over iWARP

to enable SyncMirror replication

5. A customer requires encryption at rest on every node root volume.

In this scenario, which two encryption solutions will fulfill this requirement? (Choose two.)

NVE

IPsec

NAE

NSE

6. You have a 2-node switchless cluster named clusterA. You are planning on adding two additional nodes to clusterA.

What must you consider before you add the addiHonal nodes to clusterA?

Convert clusterA to a switched cluster by migrating the data lIFs from direct connect to die cluster interconnect switch.

Convert clusterA to a single-node cluster.

Convert clusterA to a switch** cluster by migrating the cluster LIFs from direct connect to the cluster interconnect switch.

Use direct connect to add the additional nodes to cluster

7. You are expanding an existing cluster that uses BES-53248 cluster interconnect switches. You connected the new controllers to ports 0/17 through 0/20. However, you are unable to join the new nodes to the cluster.

Which action must be taken to solve the problem?

Install the license file.

Install the CSHM configuration file.

Install the reference configuration file.

Reboot the controllers.

8. After the successful installation of a NetApp ONTAP cluster, the customer wants to know how to view telemetry data. The customer also wants to receive online information about any risks with the cluster and potential best-practice gaps.

Which tool satisfies the customer’s requirements?

Active IQ Digital Advisor

Interoperability Matrix Tool

Spot by NetApp

Cloud Manager

9. You are adding new controllers to an existing cluster. As part of the upgrade process, you have updated the BES-53248 cluster switches. In this scenario.

Which two commands would you use to verify a healthy cluster after the upgrade? (Choose two.)

network port show -ipspace Cluster

network interface show -vserver Cluster

network device-discovery show -protocol cdp

network interface show -vserver Cluster -fields auto-revert

10. After completing an installation, the customer wants to know how they can manually open a new technical case with NetApp Global Support.

What are three ways to accomplish this task? (Choose three.)

Use the support site.

Use the NetApp Field Portal.

Use the mobile app.

Use a telephone.

Use AutoSupport.

Page 2 of 8

11. When you start a new Service Event Report, what must be entered first?

the case ID number

the project number

the node serial number

the sales order number

12. You are installing an AFF A700 system with two disk shelves using ADPv2. After setting up the cluster, you realize that one drive shelf was powered off and that the drives have not been assigned to any of the nodes.

In this scenario, which two resources will help you find a solution? (Choose two.)

Active IQ Config Advisor

NetApp Documentation Center

NetApp Knowledge Base

Active IQ Digital Advisor

13. A customer is creating a new SVM to host iSCSI LUNs for a Hyper-V cluster. You need to successfully map the new LUNs and make them visible to the Hyper-V cluster.

In this scenario, which host information is required to accomplish this task?

IQNs

WWNNs

WWPNs

host names

14. You have a 2-node FAS8300 ONTAP 9.8 cluster that serves SMB shares. You are configuring interface groups for higher performance and resiliency.

Which two NetApp best practices should you follow to satisfy these performance and resiliency requirements? (Choose two.)

Use ports from different NICs.

Use ports from the same NICs.

Use ports with different chipsets.

Use ports with the same chipsets.

15. Click the Exhibit button.

After installation of a new ONTAP cluster, you experience a problem. You successfully create a support case on the NetApp Support site. The customer asks you how to view the status of the case.

Referring to the exhibit, which two steps would allow the customer to accomplish this task? (Choose two.)

Open https://support.netapp.com, using the partner credentials.

Open https://support.netapp.com, using the customer credentials.

Open My Cases, and select the 41747189 case number.

Open My Cases, and select Create a Case.

16. You are setting up a peer relationship between two ONTAP clusters.

In this scenario, which two statements are true regarding authentication?

Peering authentication status can be verified with the cluster peer show command.

Peering authentication can be configured using LDAP users and groups.

Peering authentication is required before enabling peering encryption.

Peering authentication can use an ONTAP generated passphrase.

17. You have a 2-node FAS8300 switchless ONTAP 9.8 cluster that serves NAS volumes. You have a data SVM that connects to the network using multimode LACP with VLAN tags.

In this scenario, which front-end FAS8300 network port would you create the data LIFs?

a0a

e0e

e0e-100

a0a-100

18. You installed a new 2-node FAS500f ONTAP 9.8 switchless cluster that serves NAS volumes to both NFSv4.1 and SMB clients. The host operating systems have full flow control enabled on their data ports.

In this scenario, which two flow control settings would you verify? (Choose two.)

Verify that the data network ports have full flow control disabled.

Verify that the cluster network ports have full flow control enabled.

Verify that the data network ports have full flow control enabled.

Verify that the cluster network ports have full flow control disabled.

19. Click the Exhibit button.

You are attempting to add a new ONTAP 9.7 node to your ONTAP 9.8 NetApp cluster.

After attempting to add the node, it fails as shown in the exhibit.

What are two nondisruptive ways to add the new node to your ONTAP cluster? (Choose two.)

Revert the cluster from ONTAP 9.8 to ONTAP 9.7.

Re-initialize all the nodes in the ONTAP cluster with ONTAP 9.7.

Upgrade the new node from ONTAP 9.7 to ONTAP 9.8.

Add the node using the -allow-mixed-version- parameter.

20. Your customer is migrating data from a legacy FAS8020 system that runs ONTAP 9.5 software to a new AFF A250 MetroCluster over IP configuration.

In this scenario, which two methods would be supported to migrate the data? (Choose two.)

Perform a controller swap from the FAS8020 to the AFF A250s.

Create a 4-node cluster on one side and use the vol move command to migrate the data.

Use a host-based copy migration method.

Configure a SnapMirror copy between the FAS8020 and the AFF A250 systems.

Page 3 of 8

21. Click the Exhibit button.

A customer wants to replace their ONTAP cluster CN1610 switches with Cisco Nexus 3132Q-V switches. They want to perform a non-disruptive upgrade.

Referring to the exhibit, which cable will be required to non-disruptively migrate to the new switches?

a 10GbE SFP+ to SFP+ cable

a 100GbE QSFP28+ to 4x25GbE SFP28+ cable

a 40GbE QSFP+ to QSFP+ cable

a 40GbE QSFP+ to 4x10GbE SFP+ cable

22. After the installation of a new ONTAP 9.8 cluster, you have to verify if AutoSupport works.

In this scenario, which two commands would you use to accomplish this task? (Choose two.)

system node autosupport history show

system node autosupport check show

system node autosupport destination show

system node autosupport invoke

23. An iSCSI LIF fails to migrate during a storage failover test. In this scenario, why did the LIF not migrate?

A failover port was not defined

LIFs that serve block protocols do not failover

The failover policy was not configured

LIF failover was not enabled

24. After you install an AFF A700 2-node cluster with DS224C shelves, Config Advisor reports that your SAS cabling is in mixed-path HA. You expected the SAS cabling be in quad-path HA.

You physically verify the LED status on the controllers and the shelves and notice no irregularities. However, a reboot of the SAS expander does not change the output.

In this scenario, what should you do next?

Open a case with NetApp Support and turn off the disk shelves until the issue is solved.

Disconnect the disk shelves from the controller and run Config Advisor again.

Re-seat the SAS IO modules of the affected AFF A700 controller.

Use multipath HA because it is the only cabling supported on an AFF A700 controller.

25. A customer is asked to install a new AFF ASA A700 system. During the installation, the customer asks if ONTAP 9.8 is supported with their host’s OS version running Windows 2016.

In this scenario, which NetApp tool would verify supportability?

ONTAP System Manager

Active IQ Unified Manager

Active IQ OneCollect

Interoperability Matrix Tool

26. You completed a 2-node AFF A700 installation according to the poster. You run the disk show -fields owner command and notice that all drives are assigned to node 1.

In this scenario, which tool would you use to access documentation and guidelines to solve the issue?

Active IQ Unified Manager

Active IQ One Collect

NET2

NetAppDocs

27. Click the Exhibit button.

You are installing a new AFF All SAN Array A700 HA pair.

Referring to the exhibit, which IP address would have been used to join node 02 to the cluster during setup?

192.168.0.112

169.254.212.198

169.254.145.151

192.168.0.101

28. You are deploying an 8-node AFF A700 by using BES-53248 cluster switches. During the installation, you notice that ports higher than 16 are not coming online. You verify that the additional licenses are installed.

Which two additional steps must be taken to bring the additional ports online? (Choose two.)

Reload the firmware

Reload the RCF file

Re-enable each port

Reload the switch

29. Your customer wants to know more about the network configuration within the cluster.

In this scenario, which statement is correct about a LIF?

A LIF is a port that provides physical connections.

A LIF is created within a broadcast domain and contains a pool of IP address.

A LIF is an IP address or a WWPN that is associated with a port.

A LIF separates network domains to access cluster data.

30. Which two switch operating system are supported on ONTAP cluster switches? (Choose two.)

Brocade FOS

Cisco NX-OS

Cisco IOS

Broadcom EFOS

Page 4 of 8

31. Which command would be used to measure the throughput and latency of traffic between nodes?

qos statistics workload performance show

cluster ping-cluster

network test-path

statistics node show

32. You are preparing to physically install a new AFF A400 cluster into a customer’s racks. All equipment has been delivered to the customer’s site.

Which three tools do you need to complete this installation? (Choose three.)

additional network cables

Phillips #2 screwdriver

laptop computer

slide rail kit

cable management tray

33. You want to enable secure communication with the SP or BMC through CA-signed certificates.

Which two certificate types must be installed in this scenario? (Choose two.)

cluster certificate

server certificate

root CA certificate

ONTAP certificate

34. An administrator issued the cluster setup command and configured a 2-node ONTAP 9.8 cluster.

In this scenario, which tool would the administrator use to validate the configuration?

Active IQ Upgrade Advisor

Interoperability Matrix Tool

NetAppDocs

Active IQ Config Advisor

35. You are installing a new six-node ONTAP 9.8 cluster. You have completed the initial configuration of the cluster interconnect switches and the ONTAP cluster.

In this scenario, which feature should you enable?

cluster switch logging

cluster switch health monitor

IPv6 on all cluster ports

data center bridging protocol

36. Click the Exhibit button.

You are preparing to replace a Cisco Nexus 92300YC switch. You have executed the cluster ping-cluster node1 command and received the output as shown in the exhibit.

Which two checks indicate that the cluster is ready for the replacement to be performed? (Choose two.)

2 paths up, 0 paths down (TCP check)

2 paths up, 0 paths down (UDP check)

larger than PMTU communication succeeds on 4 path(s)

basic connectivity succeeds on 4 path(s)

37. Which logical interface has a fixed firewall policy?

data LIF

cluster management LIF

cluster LIF

intercluster LIF

38. You configured AutoSupport and are trying to send a full AutoSupport message to NetApp. You use the autosupport history show command and see the output shown in the exhibit. The customer confirms that the AutoSupport settings are correct.

Which two actions will solve this issue? (Choose two.)

The customer needs to enable AutoSupport for both nodes.

The customer needs to exclude the two nodes from the attachment-size limitation.

The customer needs to change the transport protocol to HTT

The customer needs to white-list the two nodes on their mail server.

39. You are preparing to install a new 2-node AFF A250 system at a customer site with an existing cluster that uses NetApp CN1610 cluster interconnect switches.

In this scenario, what are two valid actions for this installation? (Choose two.)

Add the new nodes to the existing cluster and switches.

Create a new 2-node switched cluster that uses the CN1610 cluster switches.

Create a new 2-node switchless cluster.

Migrate the existing cluster to new switches and add the new nodes.

40. You are asked to install six shelves to a production cluster. The cluster is running clustered Data ONTAP and is a 4-node cluster. All six shelves will be cabled to the same HA pair. The customer wants you to assign all the new disks to a single node in the cluster.

Which three tools would help you accomplish this task? (Choose three.)

the Hardware Universe Web-based tool

the Synergy application

the Config Advisor application

the My AutoSupport Web-based tool

the System Setup application

Page 5 of 8

41. On which type of network interfaces are the cluster interconnect LIFs created?

on an FC or FCoE port

on an interface group

on a UTA port shared with other LIFs

on a physical port

42. A host cannot connect to the namespace configured on an NVMe-enabled SVM.

In this scenario, what are two reasons for this problem? (Choose two.)

The namespace has not been added to the subsystem

The namespace has not be added to the igroup

The igroup has an incorrect NQ

The subsystem has an incorrect NQN

43. You have added two new AFF A250 nodes to an existing 4-node cluster with NetApp CN1610 cluster network switches. Although the nodes can join the cluster, the storage failover show command output shows that the NVRAM log is not synchronized, and it cannot reach the partner over an HA interconnect.

In this scenario, which two statements are true? (Choose two.)

The AFF A250 requires switches with 40GbE port support.

The AFF A250 uses different ports for the cluster and the HA interconnect.

The AFF A250 requires switches with 25GbE port support.

The AFF A250 uses the same port for the cluster and the HA interconnect.

44. 1.Your customer currently has a 4-node AFF A400 cluster that runs ONTAP 9.8, with two NS224 shelves that are connected to each HA pair. The customer needs to add additional capacity to the cluster.

Which two actions would enable the customer to accomplish this task? (Choose two.)

Connect the new NS224 shelves to the existing NS224 shelves and adjust the shelf IDs.

Connect the new NS224 shelves to the existing Cisco Nexus 3232C switches.

Deploy a new AFF A400 to the cluster.

Deploy new, dedicated, storage switches for the new NS224 shelves.

45. You want to add an AFF A400 HA pair to an existing cluster.

In this scenario, which LIF type is required?

cluster-mgmt

intercluster

data

node-mgmt

46. You want to disconnect a DS224C shelf with 3.8 TB NetApp Storage Encryption (NSE) SSDs to an AFF A300 HA pair with two DS224C shelves with 3.8 TB SSDs without NSE in one stack.

In this scenario, how would you add the shelf?

Add the shelf to the existing stack.

Create a new stack on the HA pair to add the shelf.

Connect the shelf to an HA pair with NSE drives.

License NSE and add the shelf to this HA pair as a new stack.

47. Upon finishing the Installation of a new system for a customer, they request that you train them on how to administer the system. In this scenario, which two responses are appropriate? (Choose two.)

Visit the NetApp MySupport Site and look for the Express Guides, they will guide you through the daily tasks and provide input and output examples.

If you have a specific issue, you can visit the Knowledge Base Web site (https://kb.netapp,com).

The answers to any of your questions can be found on the NetApp SmartSolve site (http://smartsolve.netapp.com).

You should open a case with NetApp Support for all future questions with low priority and include the keyword "Training" in the title.

48. You want to add two new nodes to an existing 4-node cluster.

In this situation, what must be considered regarding the cluster interconnect?

When a new node joins a cluster, IP addresses are generated automatically

When a new node joins a cluster, IP addresses are used from the data LI

When a new node joins a cluster, the customer must give you IP addresses from the customer's local IP range.

When a new node joins a cluster, you must use "class A" subnet settings.

49. Your customer wants a newly installed AFF C190 cluster to send SNMP notifications to a trap host called OVERWATCH01.

In this scenario, which two statements are correct? (Choose two.)

Configure an SNMP community string on the cluster.

Configure DNS on the cluster.

Configure a trap host on the cluster.

Configure a firewall policy and allow SNM

50. After adding two nodes to an FC-enabled cluster, the storage administrator wants to ensure that existing LUNs can use paths on the new nodes.

What is required to complete this task?

Use the storage port rescan command.

Use the lun mapping add-reporting-nodes command.

Use the lun bind create command.

Rescan the bus on the hosts by using the rescan-scsi-bus.sh script.

Page 6 of 8

51. Which two statements are true about the LIFs that are used for a cluster peer relationship? (Choose two.)

The MTU size must be set to 9000 bytes on all the LIFs used for the cluster peering.

The LIFs must use the default intercluster service policy.

The LIFs must be in dedicated broadcast domains an IPspaces.

At least one LIF per node is required on each cluster.

52. Click the Exhibit button.

Immediately after installing a 4-node FAS8200 cluster, you discover that node, “cluster1-02”, must be removed from the cluster. You want to use the cluster remove-node command to remove the node.

Referring to the exhibit, which two statements are correct? (Choose two.)

Verify that high availability is configured for failover to the HA partner, then remove the node.

Make the node ineligible by using the cluster modify -eligibility false command, then remove the node.

Move Epsilon to cluster1-02, then remove the node.

Remove the node, then the cluster will elect a new master to remain in quorum.

53. What is the main function of ACP?

it allows cabling the shelf to two additional controllers.

It allows the controller to use Ethernet instead of SAS to fetch the storage data.

it allows the controller to nondisruptively reset the SAS expanders.

It enables the automatic shelf ID assignment.

54. You installed a new 4-node AFF A400 ONTAP 9.8 cluster. The AFF400 controller data ports were automatically discovered by “automatic port placement”.

In this scenario, which two ONTAP network settings were automatically configured? (Choose two.)

routes

IPspaces

broadcast domains

subnets

55. You installed two separate clusters in an isolated data center without outbound network access. The customer wants to troubleshoot issues locally and also create custom Excel reports for capacity utilization from a local server.

In this scenario, which NetApp tool would satisfy this requirement?

Active IQ Digital Advisor

Active IQ Unified Manager

Cloud Insights

ONTAP System Manager

56. You want to create a data volume on aggr0 and you receive a message with the following warning: ''Warning: You are about to create a volume on a root aggregate.

This may cause severe performance or stability problems and therefore is not recommended. Do you want to proceed?''

What is the reason for this severe performance or stability problem?

Controller failover and storage failover are separate processes that must occur in parallel, otherwise problems will arise.

The performance load generated by the data volume can be very strong, so it should not be shared with vol0 on aggr0, requiring a separate aggregate for it.

The performance load generated by the vol0 cannot be shared with any other volume on aggr0, requiring a dedicated aggregate for it.

Controller failover and storage failover are separate processes that must occur at different times, otherwise problems will arise.

57. You are deploying a new AFF All SAN Array A250 into a customer’s existing data fabric.

In this scenario, which two tools would give insight into their existing Cisco MDS fabric configuration? (Choose two.)

Brocade SAN Health

Cisco Data Center Network Manager (DCNM)

Active IQ

Active IQ Config Advisor

58. You are expanding an existing 4-node ONTAP 9.8 cluster with a FAS8300 HA pair by adding a new FAS500f HA pair. Before the expansion, you are asked to save the configuration of the cluster to a backup file.

In this scenario, which two ONTAP configuration backup methods are available? (Choose two.)

storage VM

node

cluster

switch

59. What is the minimum number of disks required in a SAS shelf?

half of the shelf's capacity

one

two

there is no minimum

60. You were dispatched to install a cluster made up of FAS8060 and FAS8080 controllers. There are three FAS8060 controllers and three FAS8080 controllers.

Which solution would provide the largest possible cluster?

a cluster made up of two nodes

a cluster made up of four nodes

a cluster made up of five nodes

a cluster made up of six nodes

Page 7 of 8

61. You completed the installation of an AFF A700s with NetApp CN1610 switches. You used ports e0a and e0f with breakout cables to connect the controllers to the interconnect switches. After completing the cluster setup, ports e0e and e0i are not visible in OnCommand System Manager.

In this scenario, what caused this problem?

Breakout cables were used and the second port on the same ASIC became disabled.

This is a hardware error and you must open a case with NetApp Support.

You must first enable the ports using the network port modify command.

You are missing a license to enable those ports.

62. When creating a new 3.8 TB SSD-based aggregate, what is the default RAID type used with ONTAP 9.8?

RAID 4

RAID-TEC

RAID 0

RAID DP

63. Click the Exhibit button.

Referring to the numbers shown in the exhibit, which port on an AFF A220 controller is used as port e0M in ONTAP?

64. You want to use the NetAppDocs tool to collect information on a newly configured ONTAP 9.8 cluster and to generate a Word document with the details of the cluster configuration.

Which two data sources would you use to collect the necessary data? (Choose two.)

Active IQ Digital Advisor

Active IQ Unified Manager

ONTAP Cluster

AutoSupport packages

65. You are using Broadcom BES-53248 switches for a cluster interconnect in a base configuration.

In this scenario, what is the minimum number of ISLs supported between the switches?

66. After the Installation of a new NetApp FAS system, you use theNetAppDocs tool for site design documentation.

In this scenario, in which three document formats would you create an inventory report? (Choose three.)

.docx

.html

.pdf

.ps

.xlsx

67. You have a new 2-node FAS8700 ONTAP 9.8 cluster. One of the nodes has 24x16 TB NL-SAS disks assigned and available for a new aggregate. You created the aggregate with one RAID group and two spare disks.

In this scenario, how many data drives are in the aggregate?

68. A customer wants to enable SnapMirror Synchronous across their environment. The customer must ensure that SnapMirror Synchronous will work across the environment.

In this scenario, which two statements are true? (Choose two.)

A SnapMirror license is required on both the source cluster and the destination cluster.

A SnapMirror Synchronous license is required on both the source and destination clusters.

A SnapMirror license is not required on both the source cluster and the destination cluster.

A SnapMirror Synchronous license is required on the source cluster.

69. After moving a new AFF A400 cluster into production, the administrator notices error events in ONTAP System Manager regarding SAS HA issues.

In this scenario, which NetApp tool would have identified these errors after the installation process?

Cloud Manager

ONTAP System Manager

Active IQ Config Advisor

Active IQ Unified Manager

70. Click the Exhibit button.

You want to add an AFF A400 system to an existing 4-node cluster.

Referring to the exhibit, which number points to the ports that are used to cable the new nodes to the cluster interconnect switches.

Page 8 of 8

71. Data ONTAP 9 supports which three features? (Choose three.)

SMB 3.0

NFSv2

SnapMirror

Infinite Volumes

72. Click the Exhibit button.

During an ONTAP cluster handover procedure, your customer asks how to identify and solve issues that might occur on the newly deployed array.

Referring to the exhibit, which two widgets would the customer use to help with these issues? (Choose two.)

Guide Me

Active IQ

Contracts and Warranties

ASE Corner

73. Click the Exhibit button.

Which set of components on a FAS9000 are highlighted in the exhibit?

FCVI-Module, Controller, Serial-Port, FlashCache-Module

SAS-Module, Controller, USB-Port, FlashCache-Module

NVRAM-Module, Controller, Serial-Port, FlashCache-Module

Powersupply, Controller, USB-Port, NVRAM-Module

74. Your customer plans to expand a 2-node FAS2750 switched cluster with two new controllers.

In this scenario, which two prerequisites should you examine in advance? (Choose two.)

Verify that the hard drives of the new controllers are compatible with the old controllers.

Verify that the existing cluster has a minimum 10 GB of free space for root volumes.

Verify that the existing switches support the additional controllers.

Verify that the platform of the new controllers can be mixed with the cluster’s existing controllers.

75. Which switch vendor is supported for the cluster network switches?

Juniper Networks

Cisco

Brocade

Hewlett-Packard

76. Click the Exhibit button.

Referring to the exhibit, you installed a new AFF A250 HA system with FC at a customer site. The customer asks how many ports can be used for the Ethernet host connections.

In this scenario, what would you tell the customer?

77. You are preparing for the installation of a new ONTAP 9.8 cluster and need to get the preinstallation information from the customer.

In this scenario, which NetApp tool would you use to create a configuration spreadsheet template for the deployment?

Interoperability Matrix Tool

ConfigBuilder

Active IQ Config Advisor

Active IQ Unified Manager

78. You are preparing for the installation of a new 2-node switchless AFF A250 ONTAP 9.8 cluster and need to obtain the preinstallation information from the customer.

In this scenario, what are three examples of data required from the customer? (Choose three.)

management IP addresses

cluster switch name

gateway IP address

BMC IP addresses

cluster name

79. Click the Exhibit button.

You are asked to install a new cluster with six FAS8060 nodes. While running Config Advisor, you see the messages shown in the exhibit. The customer does not want ACP cabled on their cluster.

Which two actions would allow the installation to be completed successfully? (Choose two.)

Advise NGS that the customer has a controller in an unsupported state.

Advise the customer that they must acknowledge that they are not using ACP on the installation.

Advise the sales team that the customer is operating without ACP and that the customer is asking you to leave it that way.

Advise the customer that the error will cause the controller to not operate properly and create an unsupported state.

80. You are preparing to add a 2-node AFF A250 system to an existing 4-node AFF A800 cluster with Cisco Nexus 3232C switches. The cluster switches are currently running the Cluster-HA RCF.

In this scenario, which two steps are required to install the AFF A250 system? (Choose two.)

Load the Storage RC

Cable the AFF A250 nodes to the next free ports on the switch.

Cable the AFF A250 nodes to the breakout ports on the switch.

Load the Cluster-HA-Breakout RC

NetApp Certified Storage Installation Engineer, ONTAP (NCSIE ONTAP) NS0-184 Exam Dumps Updated

NetApp Certified Storage Installation Engineer, ONTAP (NCSIE ONTAP) NS0-184 Exam Dumps Updated

Here have NS0-184 free demo dumps online for checking the updated NS0-184 exam dumps:

Share this post

Author

Related Posts